Vaisala HMP60 Manual

Browse online or download Manual for Measuring, testing & control Vaisala HMP60. Vaisala HMP60 Product manual User Manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1 - Relative Humidity Probe

HMP60 Temperature andRelative Humidity ProbeRevision: 7/12Copyright © 1995-2012Campbell Scientific, Inc.

Page 2

HMP60 Temperature and Relative Humidity Probe FIGURE 4-3. HMP60 and 41303-5A Radiation Shield on a CM202 Crossarm Mounting Clamp FIGURE 4-4. HM

Page 3 - Warranty

HMP60 Temperature and Relative Humidity Probe 4.2 Step 2 — Use SCWin Short Cut to Program Datalogger and Generate Wiring Diagram The simplest method

Page 4 - Assistance

HMP60 Temperature and Relative Humidity Probe 3. Select HMP50/HMP60 Temperature and Relative Humidity Sensor then click the right arrow to add it to

Page 5 - HMP60 Table of Contents

HMP60 Temperature and Relative Humidity Probe 5. Choose the outputs for the AirTC and RH and then select finish. 6. Wire according to the wiring d

Page 6 - Figures

HMP60 Temperature and Relative Humidity Probe TABLE 5-1. Recommended Lead Lengths 2 m Height Atop a tripod or tower via a 2 ft crossarm such as the

Page 7 - Humidity Probe

HMP60 Temperature and Relative Humidity Probe Probe Body Diameter: 1.2 cm (0.47 in) Filter: 0.2 μm Teflon membrane Filter Diameter: 1.2 cm (0.47 in)

Page 8 - 4. Quickstart

HMP60 Temperature and Relative Humidity Probe 7. Installation 7.1 Siting Sensors should be located over an open level area at least 9 m (EPA) in dia

Page 9

HMP60 Temperature and Relative Humidity Probe Black Temperature Signal White Relative Humidity Signal Blue Signal & Power Reference Br

Page 10

HMP60 Temperature and Relative Humidity Probe The temperature and relative humidity signals from the HMP60 are measured using two single-ended analog

Page 11 - Generate Wiring Diagram

HMP60 Temperature and Relative Humidity Probe 7.4.2 Example for CR10X ;Measure the HMP60 temperature. ; 01: Volt (SE) (P1) 1: 1 Reps 2: 5 25

Page 13 - 5. Overview

HMP60 Temperature and Relative Humidity Probe reference and power ground are connected to ground at the datalogger. The signal reference/power ground

Page 14 - 6. Specifications

HMP60 Temperature and Relative Humidity Probe VaporPressure() instruction to calculate vapor pressure from temperature and relative humidity measureme

Page 15 - 6.1 Temperature Sensor

HMP60 Temperature and Relative Humidity Probe 7.6.2 Sample CR10(X) Program that Computes Vapor Pressure and Saturation Vapor Pressure ;Measure the HM

Page 16 - 7. Installation

HMP60 Temperature and Relative Humidity Probe 8. Maintenance The HMP60 Probe requires minimal maintenance. Check monthly to make sure the radiation

Page 17 - 7.4 Programming

HMP60 Temperature and Relative Humidity Probe 18 3. Rinse the RH chip or dispose of the old RH chip. 4. Hold the sides of the rinsed or new chip and

Page 19 - 7.5 Long Lead Lengths

Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com • info@campbel

Page 20 - 7.6 Absolute Humidity

Warranty “PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. are warranted by Campbell Scientific, Inc. (“Campbell”) to be free from defects in materi

Page 21

Assistance Products may not be returned without prior authorization. The following contact information is for US and international customers residing

Page 22

HMP60 Table of Contents PDF viewers: These page numbers refer to the printed version of this document. Use the PDF reader bookmarks tab for links to

Page 23 - 8. Maintenance

HMP60 Table of Contents ii Figures 4-1. HMP60 as shipped... 3 4-2. HM

Page 24 - 10. References

HMP60 Temperature and Relative Humidity Probe 1. Introduction The HMP60 probe measures temperature for the range of -40° to 60°C, and relative humidi

Page 25

HMP60 Temperature and Relative Humidity Probe 4. Quickstart 4.1 Step 1 — Mount the Probe Review Section 7, Installation for complete instructions.

Page 26

HMP60 Temperature and Relative Humidity Probe Yellow Shipping Cap (remove before installation)FIGURE 4-1. HMP60 as shipped FIGURE 4-2. HMP60 and 4

Comments to this Manuals

No comments