Vaisala PMB100 User Manual

Browse online or download User Manual for Unknown Vaisala PMB100. Vaisala BAROCAP Barometer PTB110 Series

  • Download
  • Add to my manuals
  • Print
  • Page
    / 4
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
www.vaisala.com M210839EN-A
1
USER'S GUIDE
Vaisala BAROCAP
®
Barometer PTB110 Series
Several pressure ranges
Accuracy ±0.3 hPa at +20 °C
Long-term stability ±0.1 hPa/year
On/off control with external trigger
Output voltage 0 … 2.5 or 0 … 5 VDC,
frequency output
Current consumption less than 4 mA
Mountable on a (35 mm wide) DIN rail
NIST traceable (certificate included)
BAROCAP
®
sensor
PRODUCT DESCRIPTION
The PTB110 barometer is a micro controller based barometer
including a voltage or frequency output. The barometer can be
supplied with several pressure ranges. The output of the
barometer is a calibrated barometric pressure reading.
The barometer uses the Vaisala BAROCAP
®
Sensor, a silicon
capacitive sensor developed by Vaisala for barometric pressure
measurement applications. The BAROCAP
®
sensor is especially
designed for accurate and stable measurement of barometric
pressure.
INSTALLATION
The PTB110 barometer is intended to be installed indoors.
Installing outdoors requires a protecting enclosure. A DIN rail
mounting option enables the mounting of the barometer on a 35
mm wide standard DIN mounting rail.
The barometer should be installed in a vertical position with the
connectors pointing downwards to prevent accumulation of
condensated water
.
OPERATING MODES
The PTB110 barometer has two operating modes, the normal
and the shutdown mode. The factory setting is the normal mode
.
Normal Mode
The device is in the normal mode when the power on
jumper is connected (see figure on the following page).
In the normal mode the barometer measures
continuously when powered-up.
Shutdown Mode
The device is in the shutdown mode when the power
on jumper is not connected.
In the shutdown mode, the barometer can be turned on
or off by switching the pin 1. The pin 1 is located at
the customer port, on the left edge of the screw
terminal.
NOTE The other jumpers inside the barometer are
set at the factory and they must not be
touched.
ELECTRICAL CONNECTIONS
The PTB110 barometer contains a screw terminal block located at
the customer port. The screw terminal includes the electrical
input/output pins presented in the table below.
Pins in screw terminal Description/Value
Pin 1: EXT_TRIG External trigger input
Pin 1 is used as a power on/off
switch in shutdown mode as
follows:
Power off 0 VDC
Power on 5 VDC
Pin 2: AGND Analog ground
Pin 3: GND Ground
Pin 4: SUPPLY Supply voltage
Pin 5: VOUT/FOUT Voltage output/
Frequency output
In the normal mode no connection to the Pin 1 EXT_TRIG is
recommended.
The barometer is protected against a reverse operating voltage.
Both grounds (AGND and GND) are in the same electrical
potential in the barometer. Both three-wire and four-wire
connections can be used. However, it is recommended to use the
four-wire connection, especially if the signal wires are long.
Page view 0
1 2 3 4

Summary of Contents

Page 1 - Barometer PTB110 Series

www.vaisala.com M210839EN-A 1 USER'S GUIDE Vaisala BAROCAP® Barometer PTB110 Series – Several pressure ranges – Accuracy ±0.3 hPa

Page 2 - PP ⋅+=

www.vaisala.com M210839EN-A 2The connections can be made as illustrated below. READING THE OUTPUT The barometric pressure (P) can be calcula

Page 3 - TECHNICAL DATA

www.vaisala.com M210839EN-A 3Dimensions TECHNICAL DATA Operating range (1 hPa=1 mbar) Description/Value 500...1100 hPa 600...1100 hPa 800.

Page 4 - WARRANTY

www.vaisala.com M210839EN-A 4SAFETY PRECAUTIONS The PTB110 delivered to you has been tested for safety and approved as shipped from the facto

Comments to this Manuals

No comments