Vaisala HydroMet User's Guide Page 174
- Page / 218
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
User’s Guide ______________________________________________________________________
172 __________________________________________________________________M210785EN-E
Scaling is performed in the following manner:
The Compression Offset value is added to the measured value. This
will reduce the number of characters in the measured value. The length
of the measured value is further reduced by omitting the decimal point
by multiplying the value with the Compression Multiplier value.
Finally, the length of the report can be reduced by omitting spacing
between the report items. Perform this by entering the correct value in
the Fixed length text box.
For example, to convert the 5-character temperature value -18.7 into the
2-character BASE32 value 9P, proceed as follows:
1. Apply the offset: -18.7 + 50 = 31.3 (-50 is minimum measured
value)
2. Scale the value: 31.3 × 10 = 313 (desired resolution 0.1 degrees)
3. Convert to BASE32. The result will be the compressed value 9P.
NOTE
The compression of the report will fail if the value is still negative after
the Compression Offset value has been added.
NOTE
The Fixed length default value applies only to the BASE32
compression. When the BCD compression is used, you must manually
adjust this parameter to match the maximum number of characters in
the numeric printout of the value. For example, if the maximum
measurement value after scaling is 99999, the Fixed length parameter
has to be set to 5.
- USER'S GUIDE 1
- CHAPTER 5 6
- List of Figures 9
- List of Tables 13
- Platform Documentation 16
- Contents of This Manual 16
- Version Information 17
- Related Manuals 17
- Documentation Conventions 18
- ESD Protection 20
- Recycling 21
- Regulatory Compliances 21
- Trademarks 21
- License Agreement 21
- Warranty 23
- PRODUCT OVERVIEW 25
- GETTING STARTED 27
- Installing Lizard 28
- 1004-047 29
- 1004-048 29
- 1004-049 30
- Updating Lizard 32
- Wizard Tool 33
- 0711-040 34
- Creating a Setup with Wizard 36
- 0802-108 37
- Figure 14 Selecting Sensors 39
- 0711-046 40
- 0309-023 40
- 0711-048 42
- 0711-050 44
- BASIC USE OF LIZARD SETUP 51
- 1004-059 52
- Selecting User Level 54
- Saving Changes 56
- Online Help 57
- User Comments 57
- Setup Management 58
- Layout of the Setup View 58
- Opening a Setup 59
- Creating a New Setup 60
- Saving a Setup 61
- Deleting a Setup 62
- Exporting a Setup 62
- Importing a Setup 63
- Exporting All Setups 63
- Importing Multiple Setups 64
- Making Backups 64
- Optional Hardware View 65
- Selecting Hardware 66
- Removing Hardware 66
- Configuring Hardware Modules 66
- Devices View 68
- Device Configurations View 69
- Non-TCP/IP Communication 70
- TCP/IP-Based Communication 70
- Common Modem Parameters 71
- Communication Interfaces View 73
- IP Services View 74
- Selecting IP Services 75
- Removing IP Services 75
- Equipment View 76
- Selecting Equipment 77
- Removing Equipment 77
- Assigning I/O Connections 78
- Re-assigning Connectors 79
- Additional Sensors View 79
- Selecting Serial Sensors 80
- Removing Serial Sensors 80
- Measurements View 81
- Editing Measurement Names 81
- Configuring Measurement 82
- Calculations View 83
- Calculation Categories 83
- Meteorological Calculations 84
- Unit Conversions 84
- Arithmetic Operations 84
- Statistical Calculations 85
- Setting up Calculations 86
- Removing Calculations 87
- Copying Calculations 87
- 0511-010 88
- Calculation 90
- Accumulator Calculation with 90
- Predefined Reset Time 90
- Advanced View 91
- Selecting Advanced Items 91
- Removing Advanced Items 92
- Logging View 92
- Setting Up Log Groups 93
- Deleting Log Groups 94
- Selecting Log Group Items 94
- Removing Log Group Items 95
- Sorting Log Group Items 95
- Selecting Log Item Options 95
- Selecting Log Group Options 96
- Storing Log Group Data 96
- Reporting Log Group Data 97
- Log Group Report Types 98
- Format String 99
- FTP Connection 100
- Sending Log Group Reports 101
- Unit Conversion in Logging 102
- Using External Memory Cards 103
- Reports View 104
- Report Templates 104
- Preformatted Report 105
- TableForm Report 105
- StringForm Report 105
- Setting up a Report 106
- Deleting a Report 107
- Filling out Reports 107
- Inserting Text into a Report 107
- Editing Reports 109
- Editing Report Properties 110
- Unit Conversion in Reports 111
- Status Conversion in Reports 112
- 0711-069 113
- Adding Preformatted Reports 115
- 0711-072 116
- 0208-058 118
- Checksum Option in Reports 121
- Binary Report 121
- Communications View 122
- Connecting Reports to 122
- Communication Ports 122
- Disconnecting Reports from 123
- Configuring Transmission 124
- Parameters 124
- Adding a Frame to a Report 124
- 0711-076 127
- Alarm Types 129
- Creating Alarms 130
- Removing Alarms 131
- Configuring Alarms 131
- Timers View 133
- Interdependence of Events 134
- Adjusting Timers 134
- Advanced Use of Timers 136
- Setup Information View 136
- Table 17 Logged Data 138
- Table 18 Reported Data 138
- Table 20 Alarms 139
- Table 21 Timed Events 139
- Script Comments 140
- 0711-080 141
- ADVANCED USE OF LIZARD SETUP 143
- SOFTWARE 143
- External Script 144
- 0711-084 145
- Changing Values of Static 147
- Parameter Sets 148
- 0711-086 149
- Daylight Saving 151
- 0811-026 152
- Time Receiver 154
- Setting System Time 154
- Reading System Time 154
- Log Sender 155
- Analog Measurement Wizard 156
- 0711-088 157
- Measurement 159
- 0605-140 160
- Manual Sensors 164
- 0711-097 165
- 23 on page 165 167
- Logging User Interaction 169
- Automatic Report Formatting 171
- 0711-099 172
- value has been added 174
- 0711-101 176
- Timer Configuration 178
- Principles of Timed Operation 178
- Modifying Timers 181
- 0711-102 182
- 0711-103 182
- Changing Timer Intervals 184
- Threshold-Dependent Timer 184
- Intervals 184
- 0711-104 185
- Interval Update Rules 187
- Single Events 188
- Multiple Events 188
- Using Static Parameters with 189
- 0711-107 190
- 0711-109 192
- Figure 96 Range Check 195
- Figure 97 Step Check 196
- Configuring Accumulator 197
- 0711-120 198
- Power Control Option 201
- 0711-193 202
- 0711-122 204
- Creating Checksum Report 206
- 0711-125 207
- 0711-127 210
- 0711-128 210
- 0711-129 213
- File Cycler 215
Related products and manuals for Networking Vaisala HydroMet
Networking Vaisala HydroMet User's Guide
(160 pages)
(160 pages)
Networking Vaisala HydroMet Service Manual
(76 pages)
(76 pages)
Networking Vaisala HydroMet User Manual
(10 pages)
(10 pages)
© 2020, manymanuals.com. All rights reserved. | 0.310 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals