Vaisala WINDCAP WS425 User's Guide Page 113
- Page / 136
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 9 ___________________________________________________________ Troubleshooting
VAISALA ______________________________________________________________________ 111
Problem Probable Cause Remedy
Data messages are not received. Baud rates of the data
logger and wind sensor
do not match.
Change the baud rate so that it is
the same in the data logger and
wind sensor.
Parameter does not change after S
command has been given.
The parameter requires
reset before it becomes
valid.
Check Table 18 on page 82
wheth
er reset is required before
the parameter is changed.
Inconsistent serial communication or
missing data.
Pin contacts of the
connector have become
oxidized or the
connector is not firmly
attached.
Change the WMT700 cable.
Error and Event Messages
If messages parameter is set to 1, WMT700 sends error and event
messages. Table 26 below lists the available messages.
Table 26 Error and Event Messages
Error/Event
Code
Probable Cause Remedy
2 Event.
Parameters have been set
to factory defaults.
You can change the default
settings in configuration mode,
see Communicating with
terminal software on page 73.
3 Event.
Wind calibration data has
been lost. WMT700 needs
to be calibrated.
Contact Vaisala technical
support.
10 Error.
You have given an invalid
value when using the S
command.
Check the allowed parameter
values, see Table 18 on page
82.
11 Error.
Parameter used with the S
command is unknown.
Check that you are using the
correct parameter names, see
Table 18 on page 82.
12 Error.
Unknown command.
Check the allowed commands
in Appendix A, Complete
Comm
and Set for WMT700, on
page 1
21.
13 Error.
String before the end of
command character is too
long.
Check the command and
parameter names that you are
using.
- USER'S GUIDE 1
- Table of Contents 3
- CHAPTER 5 4
- CHAPTER 6 4
- CHAPTER 10 6
- APPENDIX A 6
- APPENDIX B 6
- APPENDIX C 6
- APPENDIX D 6
- List of Figures 7
- List of Tables 9
- Version Information 12
- Related Manuals 12
- Documentation Conventions 13
- Recycling 15
- Regulatory Compliances 15
- Trademarks 16
- Warranty 16
- PRODUCT OVERVIEW 17
- 1003-005 18
- 1104-064 20
- Accessories 22
- Bird Cage 23
- WM Verifier 24
- Table 7 WMT700 Cables 25
- FUNCTIONAL DESCRIPTION 27
- 1005-007 28
- Calculations 30
- Overview 31
- Scalar Averaging 32
- Vector Averaging 33
- Measurement Methods 34
- INSTALLATION 37
- WARNING 38
- Installation Procedure 40
- Unpacking Instructions 41
- Mounting 42
- 1006-077 44
- 1006-079 47
- 1103-054 49
- Alignment 50
- 0208-025 51
- 1001-018 51
- 1104-086 53
- Cable 2m and Cable 10m 55
- 1009-016 56
- 1103-061 58
- Powering 60
- 1104-054 61
- 1104-055 61
- SERIAL COMMUNICATION AND 63
- ANALOG OUTPUT 63
- Protocols 65
- Serial Interface Timing 66
- Analog Output 67
- Analog Output Types 68
- Analog Output Scaling 68
- Voltage 8 mV / mph 69
- Voltage 4 mV / ° 69
- S aout1minv,0.1 70
- S aout1maxv,5 70
- CONFIGURATION COMMANDS 73
- Mode Switching Commands 76
- Parameters Handling Commands 76
- G — Get Parameter 78
- Display Port Settings 79
- START — Start Continuous 80
- Measurement 80
- STOP — Stop Wind Measurement 80
- Information Commands 82
- Configuration Parameters 83
- Configuring Data Messages 85
- Items for Data Messages 86
- Status Flags 88
- S wndOrientation,0 90
- OPERATION 93
- Program 94
- Data Messages 94
- WMT700 Data Message 21 96
- WMT700 Data Message 22 97
- WMT700 Data Message 23 98
- WMT700 Data Message 24 99
- WMT700 Data Message 25 100
- Missing Readings 101
- Measurement Mode Commands 102
- WMT700 Profile Commands 103
- MEAS — Start Measurement 104
- POLL — Poll Data 105
- SLEEP — Enter Low-Power Mode 105
- @a M 12<CR><LF> 106
- MAINTENANCE 107
- Visual Inspection 108
- Cleaning 108
- Testing Proper Operation 108
- 1005-003 109
- TROUBLESHOOTING 111
- Error and Event Messages 113
- Technical Support 116
- Product Returns 116
- TECHNICAL DATA 117
- Table 31 General 119
- Table 32 Accessories 120
- Dimensions 121
- 1103-055 122
- TYPICAL SYSTEM ENVIRONMENTS 125
- 1003-052 126
- 1004-001 128
- CONFIGURATION PARAMETERS 131
Related products and manuals for Measuring, testing & control Vaisala WINDCAP WS425
(169 pages)© 2020, manymanuals.com. All rights reserved. | 0.643 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals