Vaisala HMD70U Service Manual Page 75

  • Download
  • Add to my manuals
  • Print
  • Page
    / 162
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 74
73
For more information, visit
www.vaisala.com or contact
us at sales@vaisala.com
Ref. B210375EN-C ©Vaisala 2011
This material is subject to copyright protection, with all
copyrights retained by Vaisala and its individual partners. All
rights reserved. Any logos and/or product names are trademarks
of Vaisala or its individual partners. The reproduction, transfer,
distribution or storage of information contained in this brochure
in any form without the prior written consent of Vaisala is strictly
prohibited. All specifications — technical included — are subject
to change without notice.
Operating Environment
Temperature *) -40 ... +60 °C (-40 ... +140 °F)
Relative humidity 0 ... 100 %RH
Pressure *) 0 ... 50 bar
a
(725 psia)
Sample flow rate no effect for measurement accuracy
*) For extended temperature down to -40 °C (-40 °F) or pressure
up to 50 bar
a
(725 psia) the supply voltage must be 24 ... 28 VDC.
Outputs
Analog output (scalable) 4 ... 20 mA (3-wire), 0 ... 1 V/5 V
Resolution for current output 0.002 mA
Resolution for voltage output 0.3 mV
Typical temperature dependence 0.005% of span / °C
Connector 4-pin M8 (IEC 60947-5-2)
connection cable with snap-on or thread locking available
RS232 serial line for service use with DMT142RS cable
General
Sensor Vaisala DRYCAP
®
180D
Measured gases non-corrosive gases
(SF
6
gas with special model)
DEW POINT ACCURACY VS. MEASUREMENT CONDITIONS
Dew point accuracy range for the extended version. Standard
version with dotted line.
Response time 63% [90%] at +20 °C gas temperature and 1 bar
pressure
-60 -> -20 °C T
d
(-76 -> -4 °F T
d
) 5 s [10 s]
-20 -> -60 °C T
d
(-4 -> -76 °F T
d
) 45 s [10 min]
PPM VOLUME CONCENTRATION
Measurement range 70 ... 200 000 ppm
Accuracy at +20 °C (+68 °F), 1013 mbar 7.3 ppm + 9.2% of reading
Accessories
Connection cable for DM70 211917ZZ
Service cable for serial line DMT142RS
Sampling cells
basic sampling cell DMT242SC
with Swagelok 1/4" male connectors DMT242SC2
with quick connector and leak screw DSC74
two-pressure sampling cell DSC74B
cooling/venting coil DMCOIL
See DM70 / Portable Sampling Systems and Sampling Cells for
further information about sampling cells available
Loop powered external display 226476
Dewpoint temperature (°C)
Temperature of measured gas (°C)
Dewpoint accuracy range for the extended version. Standard version with dotted line.
0
40
-60
-80
10
20
30
50
60
70
-10
-20
-30
-50
-40
-70
80
0
-10
-20
-30
-40
10
20 30
40
50
60
Dewpoint measurement range lower limit
Accuracy ±3 °C Td
or better
Water vapor saturation line
Accuracy ±4 °C Td
Std version ±3 °C range
or better
Not recommended area
for continuous measurement
AW24
G1/2” ISO 228/1
58 22.5
92.5
Ø12
Ø28
Dimensions
in mm
Recommended calibration interval
to confirm the specified accuracy 2 years
Operating voltage with voltage output 12 ... 28 VDC
Operating voltage with current output 18 ... 28 VDC
Supply current
normal measurement 10 mA + load current
during self-diagnostics max. 220 mA pulsed
Load for current output max. 500 ohm
Load for voltage output min. 10 kohm
Housing material stainless steel body (AISI316L) plastic
cap(ABS/PC)
Sensor protection stainless steel sintered filter
Mechanical connection G1/2” ISO 228-1 thread
with bonded seal ring (U-seal)
Housing classification IP64 (NEMA 3S)
Storage temperature range -40 ... +80 °C (-40 ... +176 °F)
Weight 118 g (4.16 oz)
Complies with EMC standard EN61326-1, Electrical equipment for
measurement, control and laboratory use - EMC requirements;
Industrial environment.
Page view 74
1 2 ... 70 71 72 73 74 75 76 77 78 79 80 ... 161 162

Comments to this Manuals

No comments